How to Use X4 Labs – Instructions and Videos

 
The instructional videos produced by X4 Labs will be very helpful if you are using their extender for the first time. See below the official X4 Labs how to use videos along with short summaries of the clips.

How to: Introduction

This video features a pictorial of the device and its major components. The 3 basic parts are: 1) base assembly, 2) tension bars, and 3) hybrid support piece. The device is shipped preassembled so you don’t have to worry about putting it together.

It is fully adjustable and designed ergonomically for the ultimate in comfort.

Visit the Official X4 Labs Site

How to: Add Tension

This video depicts how to add the correct amount of tension to your penis using the extender. First, you must remove the support piece, which easily slides off (it is located opposite of the base). Next, screw the two 2-inch tension bars, in a clockwise motion, into the two bars coming out of the base. Next, slide the support piece back on, making sure it fits snugly in place.

Visit the Official X4 Labs Site

How to: Interchange Support Pieces

This video shows you how to interchange the support pieces of the device (replacing the hybrid support piece with the quad support piece). First, remove the hybrid support piece by gently sliding it off. Next, with the curve on the base pointing downwards, line the tension bars up with the holes on the quad support piece. Gently but firmly push the support piece towards the base until it fits snugly.

Visit the Official X4 Labs Site

How to: put on the Silicone Harness

This video explains how to put on the silicone harness with your device.

Before starting, make sure the tension bars are long enough for your penis to fit between them comfortably. Next, slide the device over the top of your penis with the support piece on the bottom. Ensure that it fits snugly & comfortably on the base. Now thread the silicone harness through the hole in the space-age foam padding. Thread it all the way through so that the padding is centered on the harness. Next, thread each end of the harness through the top holes in the support piece as far as you can, making sure that they are threaded evenly. Next, gently insert your penis head into the loop formed by the harness. Next, use one hand to compress the device while using your other hand to tighten the harness while you lock it into place.

Visit the Official X4 Labs Site

How to: put on the Comfort Strap

This video shows you how to put on the comfort strap with your device. First, ensure that the tension bars are long enough for your penis to fit securely and comfortably between them. Next, slide the device over the top of your penis with the support piece on the bottom.

Ensure that it fits comfortably but securely on the base. Find a short, circular piece of space-age foam padding and stretch it out with your fingers (rolling them around inside the circular foam much like you would a rubber band). Next, slide the foam over the penis, fitting it just below the head. Next, locate the corresponding comfort strap and, with the curve on it facing away from your penis head, thread the two ends of the strap through the slots on the support piece of the device. Next, gently guide your penis head into the circle formed by the comfort strap. Once you have it comfortably inserted, use one hand to compress the device and the other hand to tighten the comfort strap

Visit the Official X4 Labs Site

How to: put on Velcro Strap

This video depicts how to put on the Velcro strap with your device. First, ensure that the tension bars are long enough for your penis to fit securely and comfortably between them. Next, slide the device over the top of your penis with the support piece on the bottom. Ensure that it fits comfortably but securely on the base. Find a short, circular piece of space-age foam and stretch it out with your fingers (rolling them around inside the foam like you would a rubber band).

Next, slide the foam over your penis and fit it just below its head. Find the Velcro strap, noticing that it has both a soft side and a prickly side. With the prickly side facing out, guide one end of the strap through one of the slots on the support piece of your device. Wrap that same strap end around the support piece and guide it back through the other slot towards your penis. Next, while compressing the device, wrap the ends of the strap around your penis so that the strap wraps around the space age foam’s center. If your strap is too wide to adequately fit into the center of the foam, you may have to trim it to size.

How to: fine tune the Traction feature

This video explains how to fine-tune the traction used by your device. In order to fine-tune the traction, you must be wearing the device. First, prior to fastening your device, you must press down on your support piece in order to compress the tension springs. The three lines seen there (which signify 700 g, 1400 g, and 2100 g from top to bottom) can be used to judge how much tension you wish to apply.

You should use only the amount of tension necessary and not overdo it. The two screws located on the bottom of the springs can be used to tighten up (or loosen) the tension. Turning the screws clockwise will provide more tension while turning them counter-clockwise will reduce the tension.

Visit the Official X4 Labs Site